Ford vehicle guide · Michigan City Ford · Michigan City, IN

Ford Explorer Key Fob Battery

What battery does a Ford Explorer key fob take, and how do you change it? Here is what Ford's 2027 Explorer® Owner's Manual says for push-button-start remote controls, step by step.

Michigan City Ford dealership building
Illustrative photo
CR2450Coin-type 3-volt lithium battery
5 stepsFord's replacement procedure
+ side upHow the new battery goes in
Backup slotIf the fob is not detected

The short answer

Ford says the push-button-start Explorer remote control uses one coin-type 3-volt lithium CR2450 battery or equivalent. Pull out the key blade, twist a thin coin under the hidden tab to remove the cover, use a screwdriver to carefully remove the old battery, and install the new one with the + side facing up. Replacing the battery does not erase the programmed key. Other model years may differ; check your own owner's manual.

What battery does the Explorer key fob use?

Ford's 2027 Explorer manual lists these remote control batteries:

Remote controlBattery Ford lists
Push-button-start remote controlOne coin-type 3-volt lithium battery, CR2450 or equivalent
Police versionsOne coin-type three-volt lithium battery, CR2032 or equivalent

When the battery is getting weak, Ford lists a "Key battery low Replace soon" message, which means it is time to replace the remote control battery.

From Ford's 2027 Explorer® Owner's Manual (edition date June 2026), pp. 68-72, read November 17, 2026.

How to replace the Explorer key fob battery

Ford's steps for the push-button-start remote control:

  1. Push the release button and pull the key blade out.
  2. Twist a thin coin under the tab hidden behind the key blade head to remove the battery cover.
  3. Insert a screwdriver and carefully remove the battery.
  4. Install a new battery with the + side facing upward.
  5. Reinstall the battery housing cover onto the transmitter and install the key blade.

Steps from Ford's 2027 Explorer® Owner's Manual (edition date June 2026), pp. 68-69, read November 17, 2026.

Ford's notes on the battery change

Your key stays programmed

Ford says replacing the battery does not erase the programmed key from your vehicle.

Leave the grease alone

Ford says not to wipe off any grease on the battery terminals or on the back of the circuit board.

Keep coin cells from children

Ford warns to keep batteries away from children to prevent ingestion.

Recycle the old one

Ford suggests asking your local authority about recycling old batteries.

From Ford's 2027 Explorer® Owner's Manual (edition date June 2026), pp. 69-70, read November 17, 2026.

Starting the Explorer if the fob is not detected

If the Explorer shows "No key detected," Ford says the system has not found a valid passive key. Ford's manual describes a passive key backup position for push-button-start vehicles:

  1. Raise the center console storage lid.
  2. Place the remote control in the backup slot with the buttons facing toward the rear of the vehicle.
  3. Press the brake pedal.
  4. Press the push button ignition switch to start the vehicle.

From Ford's 2027 Explorer® Owner's Manual (edition date June 2026), Accessing the Passive Key Backup Position, pp. 170-172, read November 17, 2026.

Prefer to have it done for you? Our service team can help; see our Ford battery service in Michigan City page.

Explorer key fob help at Michigan City Ford

Our service team can help with your Explorer's remote control battery, along with vehicle batteries and routine maintenance. Check our service specials for current offers.

Schedule service online. Michigan City Ford is at 3930 Franklin St. in Michigan City. Get directions.

Michigan City Ford service hours

DaysHours
Mon-Fri7:30 a.m.-5:30 p.m.
Sat8 a.m.-3 p.m.
Sunclosed

From Michigan City Ford's website, November 17, 2026. Holiday hours can differ.

Ford Explorer key fob battery FAQ

What battery does a Ford Explorer key fob take?

Ford's 2027 Explorer owner's manual says the push-button-start remote control uses one coin-type 3-volt lithium CR2450 battery or equivalent.

How do I open the Explorer key fob?

Push the release button and pull the key blade out, then twist a thin coin under the tab hidden behind the key blade head to remove the battery cover.

Which way does the battery go in?

Ford says to install the new battery with the + side facing upward.

Will I need to reprogram the key after changing the battery?

No. Ford says replacing the battery does not erase the programmed key from your vehicle.

How do I start my Explorer if it says No key detected?

Ford describes a passive key backup slot: raise the center console storage lid, place the remote in the backup slot with the buttons facing the rear, press the brake pedal and press the push button ignition switch.

How do I know the key fob battery is low?

Ford lists a "Key battery low Replace soon" message for when the remote control battery needs replacing.

Can Michigan City Ford help with my Explorer key fob?

Yes. Schedule service online and our service team can help with your Explorer's remote control battery.

Sources

Battery type and steps are from Ford's 2027 Explorer® Owner's Manual (edition date June 2026), pp. 68-72 and 170-172, read November 17, 2026. Ford's own owner's manual for your vehicle governs; check it for the latest. Address and service hours are from Michigan City Ford's own website, checked November 17, 2026. Photo is illustrative.

  1. Ford: 2027 Ford Explorer Owner's Manual (edition date June 2026), remote control battery and passive key backup position, Ford Motor Company, read November 17, 2026
  2. Address and service hours (structured data), Michigan City Ford, November 17, 2026